[gunny]

Attempting to replace my front pulley with a 30 tooth as many of you have done, however ~ I cannot get the 30mm retaining nut to move. I just tried a 6pt socket and ¾ ratchet with 2’ persuader. I believe I released the tabs properly and I do know what a 100 lbs/ft feels like. What am I missing gents? RH / LH threads? I have done the search process here but no one mentions having any trouble. Your knowledgeable thoughts are needed. I feel a little foolish as it looks so straight forward. Thanks

 

[strykenshane]

Dealership did mine, 10 minutes, 20 bucks, you'll love this mod

 

[BOOLSHOT]

Where do you find the pulleys? How much do they run?

 

[gunny]

Where do you find the pulleys? How much do they run?

Yamaha Sports Plaza
22455 NE Halsey St
Fairview, OR 97024-2644
(503) 669-2000
http://www.yamahasportsplaza.com/
148.73

 

[gunny]

Dealership did mine, 10 minutes, 20 bucks, you'll love this mod

Shane - I called my local bike shop (not dealership) after I posted and if I don't get it done tonight I can bring it in tomorrow.
Thanks for this input and all the good input you have posted on this forum. More on that later @ your current seat vs Mustang.

 

[strykenshane]

Where do you find the pulleys? How much do they run?

Yamaha Sports Plaza
22455 NE Halsey St
Fairview, OR 97024-2644
(503) 669-2000
http://www.yamahasportsplaza.com/
148.73

Before ya do that try Brent at Tejas Motorsports, I know he hooked up Stryker11 and I was gonna call him myself after talking to my dealership, got mine for 99 bucks

 

[BillyD66]

I think when Fujums did his he had an impact wrench. Maybe send a shout out to him. Also check local auto parts stores for their rental tools. They have all kinds of stuff that just requires a deposit(ie no real money to rent the tool)

 

[11Stryker]

Hey Gunny, I was the first to do this and new pulley came with yami instructions. I am positive that the threads are normal right hand thread. I used a 1/2 Snap-on impact wrench to take the nut off and then torque wrench of course to tighten nut back on.

 

[gunny]

Thanks 11, I was hoping you would chime in. An impact did cross my mind but feared causing other damage. I hate it when a few minute job turns into a couple of days. Did I mention I work on ‘patience’? I’m stopping by my local bike shop this morning. Can’t wait to experience what you and others have noticed in the drive.

 

[goodhumorman19]

30t Front Pulley

Anyone have a good shop/website where I can get a new 30t front pulley?? I see most sites are about $170 for new. I checked ebay and there is nothing good

 

[jsr]

I had to use a 8ft piece of pipe and steady pressure to get mine lose and yes it is a standard rh thread. I was nervous as shet but I just put constant pressure on it and it slowly started turning.

 

[ryderjay]

When I replaced the front sprocket on my R6 race bike I found that despite the service manuals torque spec, the factory sprocket was actually much tighter. Probably the same on the Stryker.

Sent from my Galaxy S5.

 

[Adrenaline Revolution]

Air impact!
Off in seconds, Torque wrench to replace, whole job including readjusting belt tension and alignment, 1.5 hours.
Take your time Gunny, Do it yourself...
You'll be proud of the job and you'll know your bike just a little better!

 

[ravage73]

is this the right part?

http://www.2wheelpros.com/oem-parts...00-part.html?gclid=clw3l_mw3bwcfdeufgod3huacq

 

[zona]

Isn't this an old thread? But anyways. Take a breaker bar, aim it at 10:00, make sure the socket is well secured and at the handle of the bar. Step on it and put your weight down on it. After, tighten it with a torque wrench. Less than 30 min work

 

[11Stryker]

Anyone have a good shop/website where I can get a new 30t front pulley?? I see most sites are about $170 for new. I checked ebay and there is nothing good

Thats it! No aftermarket.