Joined
·
3,032 Posts
Anyone install one of these that would be willing to help out a little?
Help needed installing Kuryakyn Hypercharger
1 - 20 of 32 Posts
Joined
·
3,032 Posts
Well one thing is how to connect the vaccuum line. The instructions are very short and vague. Overall it's pretty obvious how to mount it, but I think I'm gonna go ahead and take it to a mechanic. The instructions say the carbs need to be jetted and I'm not going to mess with that.
The stryker doesn't have carb, so don't worry about that. Basically on the top of your throttle body ( the place your mount the intake to), you should see a small rubber boot. Pull the boot off and place your vacumme line onto the little dammit sticking up. I do remember the vacumme line that came with the intake was a little big. Just go to our local automotive store and get a smaller one.
Hope this helps.
Hope this helps.
Joined
·
3,032 Posts
Ok...so does it just connect it to where the vent line would go?
Also the hypercharger has some kind of plastic ring inside where the filter goes that's just floating around. Not sure what to do with it.
Also the hypercharger has some kind of plastic ring inside where the filter goes that's just floating around. Not sure what to do with it.
Urbanrage is correct, there is an unused vacuum port with a tiny rubber boot on it. Remove that and put your hose there. I recently installed a hypercharger, and the hose that came with it was the perfect size. If I remember correctly the plastic ring went on one side of the filter to make it fit correctly and not bounce around inside the housing.immortal13 said:
Joined
·
3,032 Posts
I see the port but where does it attach to the hypercharger? Do you just connect it at the bottom right instead of attaching the vent hose? That looks like the only place it could go. And yes, the hose looks like the right size.Rodekill said:
On the back side of the hypercharger in the same area as the butterflies there is a port for a vacuum hose. You can see it in the lower picture on the following page if you still have trouble locating it.
http://www.badweatherbikers.com/buell/messages/47623/193610.html?1146348386
http://www.badweatherbikers.com/buell/messages/47623/193610.html?1146348386
Joined
·
3,032 Posts
Got it installed. Thanks for the help guys. This thing looks freakin badass on my bike. I got the stinger trap door to go on the outside....looks sweet.
Now to tackle the power pro install. Thanks again
Now to tackle the power pro install. Thanks again
Joined
·
3,032 Posts
I'll try to get some up by tomorrow. I love how the butterfly flaps open up when you gas it.
Joined
·
152 Posts
Pics are a must on here.....I finally got the ol'lady to un-ass some cash so now its my time to get one. Can anyone recommend where to buy it at the best price? I'm looking for the black one to match my raven.
Joined
·
3,032 Posts
here she is with her new air breather
Attachments
Joined
·
3,032 Posts
another
Jeremy, the best price I found was phatperformanceparts.com
$150 for the hypercharger
$131 for adapter kit
$ 48 for stinger trap door
Jeremy, the best price I found was phatperformanceparts.com
$150 for the hypercharger
$131 for adapter kit
$ 48 for stinger trap door
Attachments
Joined
·
252 Posts
Looks great on the Raven bike with the Chrome Vance & Hines pipes that you have on it.
Joined
·
4,199 Posts
I dig it
Joined
·
152 Posts
It does look great and the price is nice too....Soooo where'd ya buy it at? Share the love hommie!
1 - 20 of 32 Posts
