Yamaha Star Stryker banner
1 - 20 of 33 Posts

·
Registered
Joined
·
674 Posts
Discussion Starter · #1 ·
Since the other thread has now reached 17 pages, I decided to create a new one to help clean things up a bit for future orders. If you would like to read reviews, you can visit the old thread here:
http://www.yamahastarstryker.com/9-vendor-board/28681-bar-risers-now-available-17.html

Pricing is as follows:

Plain steel: $160 / set shipped (lower 48)

Stainless steel: $180 / set shipped (lower 48)

Powdercoated steel (any color): $200 / set shipped (lower 48)

*All Active Duty Military as well as Veterans receive a 20% discount*

Everything you need will be included (including hardware). Installation is just a few 'quick' steps:
1. Remove the bars
2. Thread the spacers onto the bars.*
3. Insert bars into upper triple tree.**
4. Bolt through bottom of triple tree with supplied bolt / washer.*
5. Re-route cables as needed for proper clearance.

* Blue / Medium strength loctime is recommended but not required (not included). Some sort of lubrication is required for stainless steel to prevent gauling.
** These are made to a very close tolerance. Some minor sand paper work may be required for perfect fitment.

If my calculations are correct, these should give you a rise of approximately 1.6" and a pull back of 1.2". It doesn't seem like much, but feels like a lot more.

These are all made to order so lead time is approximately 4-5 weeks.

*Expediting is possible (typically 1-2 weeks). There is a 50% expediting fee on all expedited orders.

PM me for payment information or via email at klarowe (at) kkdgarage (dot) com.

Pics:
Adrenaline Revolution:


Klarowe:








 

·
Registered
Joined
·
674 Posts
Discussion Starter · #9 ·
Just a quick update. These should be shipping out to me early next week. I still have a couple extras (stainless steel) if anyone wants to lay claim to them. Let me know asap before they are gone!

For those who are in this order, please PM or email me your shipping address. Thanks!
 

·
Registered
Joined
·
674 Posts
Discussion Starter · #12 ·
The risers arrived yesterday. I will be doing the final thread cleaning and boxing them up tonight. They will be shipped out tomorrow and tracking information will be provided. I have 2 stainless sets left that will be going up on ebay (trying to test that market) Friday for full retail price. If anyone on here would like a set, please let me know before I put them up on ebay. Thanks!
 

·
Registered
Joined
·
674 Posts
Discussion Starter · #13 ·
Risers were all shipped out Friday. Unfortunately I left the receipt with tracking information at home but will send the tracking numbers out tonight.

This is also last call for the 2 remaining sets of stainless steel. They will be going up on ebay at a higher cost and I can't promise that I will be able to end the listings early.... Please let me know if you are interested in a set. Thanks.
 

·
Registered
Joined
·
674 Posts
Discussion Starter · #29 ·
Do you have some pictures you can send me? I will have to bring it up to my vendor because they are stainless and shouldn't be rusting... Is it the riser itself or the bolt? The bolts are the only thing that is not stainless...
 

·
Registered
Joined
·
674 Posts
Discussion Starter · #35 ·
I wish they were just a piece of pipe and a bolt then I could offer them for much less. Lol. These are precisely machines to fit the inside the triple tree to ensure there is no slop like some of the cheaper options out there. These also thread onto the bars then a bolt threads into the riser. They aren't just a spacer. There is also a step and recess machined into the riser so it fits the triple tree and riser as clean as possible.

 

·
Registered
Joined
·
674 Posts
Discussion Starter · #43 ·
Did anybody have to get new cables or can I run the same cables?
You can use the same cables, but you will need to re-route them a little bit to make sure they aren't too tight.
 

·
Registered
Joined
·
674 Posts
Discussion Starter · #44 ·

·
Registered
Joined
·
674 Posts
Discussion Starter · #45 ·
If anyone would like to be a part of this new order, I will need to know for sure by Friday. After that, I cannot make any more changes to the order. Thank you!
 
1 - 20 of 33 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top