my stryker exhaust and a few mods
1 - 20 of 26 Posts
yea i painted the headlight,speedo,and the key trim and i took off the frisbee on the rear brake caliper rotor and cleaned up the rear tire and put a dunlop 240 rear tire and the chin for the radiator that i also painted black and put the small led turn signals on and moved the plate on the side 
Joined
·
1,876 Posts
What........no pics!!! :-\ :-\
Joined
·
468 Posts
That looks and sounds great!! The 240 really sets it off!nuttieb70 said:
RSR
Joined
·
1,876 Posts
Definitely cool, you guys are getting the fever ......lol.
the turn signals r just some small LEDs I bought from our local shop and for mounting them it's just some L brackets I picked up from the hardware store and painted them black they will mount right under the center of the forks u just take off the little bracket in the middle preaty simple really
Joined
·
468 Posts
Home mods Rock! Deja knows this straight up!! X man, same same!nuttieb70 said:the turn signals r just some small LEDs I bought from our local shop and for mounting them it's just some L brackets I picked up from the hardware store and painted them black they will mount right under the center of the forks u just take off the little bracket in the middle preaty simple really
RSR
Joined
·
1,876 Posts
Im sure someone will or has an integrated LED tail light by now.
Check it out....or I will. ;D ;D
Check it out....or I will. ;D ;D
Funny you should ask... I was just checking this out yesterday.. I was about to pull the trigger, but decided to wait.. The total would have been about $210 for everything.. stated below.dejablu110 said:
For the rear - 9.8" has 20 LED Turns (2.4" long) and 35 LED Brake (4.2" long) http://www.chromeglow.com/catalog.asp?prodid=651396&showprevnext=1
This to allow the rear driving light to get brighter when the brakes are applied http://www.chromeglow.com/catalog.asp?prodid=520657
Front.. the ones that wrap around the fork http://www.chromeglow.com/catalog.asp?prodid=690309&showprevnext=1
Also with the front http://www.chromeglow.com/catalog.asp?prodid=680271
Finally the load stabilizer http://www.chromeglow.com/catalog.asp?prodid=624309
I would rather put the 200 towards the fuel controller first though.. But I am also very impatient when it comes to tinkering around with toys..LMAO...
Joined
·
1,876 Posts
well, you can get the rear....the front are usually more expensive.
You can get LED strips for the front much cheaper. You dont need
the stabilizer unless you just dont like the blinker blinking faster. I
didnt mind it.
You can get LED strips for the front much cheaper. You dont need
the stabilizer unless you just dont like the blinker blinking faster. I
didnt mind it.
Joined
·
19 Posts
The youtube video shows a side mounted license plate but does not get around the bike enough for a good look at it. Can anyone post a picture that shows what this looks like in a little more detail? It looks like you have to mount the side license plate quite a bit up front on the bike. Also, the smaller turn signals look pretty good in the video, again a close up would be absolutely fantastic.
Thanks in advance for any information.
Dave
Thanks in advance for any information.
Dave
Joined
·
468 Posts
SuperDave12, very interesting avatar! ;D
RSR
RSR
I just used one of the front turn signal brackets and cut it down and mounted the plate on the belt guard preaty sturdy really I was just going to put it on the peg bolt but couldn't get the stupid bolt out u can just use a L bracket instead u to u tho and just paint it black I will try to post a video tho
Joined
·
1,876 Posts
1 - 20 of 26 Posts
