Rear Axle Diameter

elle · Sep 30, 2011

Okay guys, forgive me if it's already been mentioned somewhere that I can't find, but what is the diameter of the rear axle? I gave up on the dealer after being on hold for at least 15 minutes. Wanting to order a side tag mount but need the diameter for this particular mount

MNStryker26 · Sep 30, 2011

road6customs.com has mounts that will fit the stryker. That is where I got mine. I am not sure the diameter though.

elle · Oct 3, 2011

That's where I was trying to order from. Can you tell me did you order SKU 00036?

MNStryker26 · Oct 3, 2011

I got 000135 since we have to have horizontal plates in Minnesota. I believe the holes are the same though.

elle · Oct 3, 2011

Okay, called them. That sku is for a gas tank or something. No horizontal tag with that sku.

MY LIFE · Oct 3, 2011

This is the one I put on.

http://www.road6customs.com/online-shop.html#ecwid:category=337153&mode=product&product=1136457

elle · Oct 4, 2011

Got it. Thx

TEMCO · Oct 4, 2011

Elle, you might have already known this but I found out from SCHIMBO that we in Fl can have vertical mount type as long as you have an Epass/Sunpass on the bike. Not sure what they have down there. It has to be mounted so its read top to bottom. Just an FYI

elle · Oct 4, 2011

Thx, Temco. I did read that. I have a Sun Pass account for the truck Just need another transponder.

UrbanRage · Oct 4, 2011

I recently fabbed a new bracket for me side mounted plate. I used a uni-bit to drill the hole for the axel. I stopped at 7/8" or 13/16" mark. The axel fit though will a tiny bit of play. I hope that might help.

If you can get a set of these.. http://www.amazon.com/Neiko-3-Piece-Titanium-Drill-Steel/dp/B001OEPYWK/ref=pd_bxgy_hi_img_b
they are extremely helpful for all type of applications.

elle · Oct 5, 2011

Thx, guys. I have a step bit, but not titanium. I ordered today. Here is the one I ordered. In the mail today. Should get it shortly.

http://www.road6customs.com/online-shop.html#ecwid:category=337153&mode=product&product=1136457

MNStryker26 · Oct 5, 2011

Elle said:
Thx, guys. I have a step bit, but not titanium. I ordered today. Here is the one I ordered. In the mail today. Should get it shortly.

http://www.road6customs.com/online-shop.html#ecwid:category=337153&mode=product&product=1136457

That is the one I got too. I am not sure where I got that SKU from on my last post. Sorry if I just confused you.

elle · Oct 5, 2011

No worries, MNSTRYKER26. I can't wait to get it installed and get the tail cleaned up!

MNStryker26 · Oct 6, 2011

Elle said:
No worries, MNSTRYKER26. I can't wait to get it installed and get the tail cleaned up!

Good luck!

Zolemite · Feb 21, 2012

Nobody actually answered this guys question. I would also like to know the axle diameter, if anybody knows? I've searched and have yet to find a definitive answer.

fujums · Feb 21, 2012

I'm fairly certain that it is 3/4. My axle mount plate bracket came pre-drilled at 3/4 and it only needed to have the burs Dremeled a little to fit right on with no play.

kraaazymike · Feb 8, 2013

Bringing back a thread from the dead, to settle an old debate: the axle diameter is 0.785". I just measured it with my calipers

Zolemite · Mar 30, 2013

kraaazymike said:
Bringing back a thread from the dead, to settle an old debate: the axle diameter is 0.785". I just measured it with my calipers

Thanks!

Rear Axle Diameter

Top Contributors this Month